ICND1 | Interconnecting Cisco Networking Devices 1

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo314.html exhibit. You want to configure a default route, so that users in the stub network are able to locate resources located in the 10.0.0.0 network. Which command can you use to configure this default route?

Refer to an excerpt of a routing table in the |h %5coutput%5ct10%5cmisc%5c100105eo309.html exhibit.

What is the metric value given for the 192.168.2.0/23 route?

Which command allows a Cisco device to automatically switch to daylight saving time?

You are troubleshooting an interface and you suspect that the issue is cable related. Which command will allow you to view framing errors?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo319.html exhibit. Based on the output from the exhibit, which router protocol is being used?

When troubleshooting RIPv2, which command will present you with information on RIP routing transactions?

Which IPv6 address is a global unicast address?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo327.html exhibit. You have configured a RIPv2 route so that users in the 10.0.0.0 network are able to locate resources located in the 172.16.1.0 network. Which command can you use to verify that the route has been successfully added to the routing table?

Why might a Cisco IOS device's startup configuration file be stored on a TFTP server? (Choose two.)

You have been tasked with setting up a new network. Within your network, host computers need to be able to reach hosts on the Internet by using readable names and converting them to numeric addresses. So you decide to configure the appropriate protocol on your router. Which protocol needs to be configured on the router?

When a Cisco switch learns about a new device on the network, what command is used to see the list of unique address associated with these devices?

Refer to the |h %5coutput%5ct14%5cmisc%5c100105eo418.html exhibit.

You want to create a static address translation between Host C on your internal network and address 172.35.116.1, which has been assigned by your ISP. Which commands would you need to enter to enable this? (Choose three.)

Which command will limit the level of system logging messages sent to a syslog server to emergency messages only?

You are troubleshooting a VLAN leaking issue. Which command would help verify the cause of this problem?

The OSI and TCP/IP models provide a visual networking reference. Which layers of the OSI Reference Model map to the link layer of the TCP/IP stack? (Choose two.)

You configured DHCP to dynamically allocate IP addresses. Which of the following is the first step of the DHCP process for configuring clients?

You need to add the following ACL entry at the top of the ACL:

deny ip host 10.1.1.25 any

Which sequence number should you use?

You have been tasked with configuring a Cisco router as a DHCP server. You need to ensure that clients receive the TFTP server's IP address as part of the DHCP configuration. Which command should be used?

Refer to an excerpt of a routing table in the |h %5coutput%5ct10%5cmisc%5c100105eo307.html exhibit.

Which of the following describes the 172.16.1.0/30 route from the output of the show ip route command?

An employee submits a support ticket indicating they are unable to reach host B on the network. You have done some troubleshooting and suspect that the issue may be DNS related. Assuming that the employee is host A, which two commands would have been used to have reached this conclusion?

An ACL has been configured to limit remote access. What can be done to monitor attempts to access the device by unauthorized sources?

You have configured a router to use EIGRP as its main routing protocol for your internal network. You would like to configure a floating static route. What would need to be configured for the floating static router's administrative distance?

You need to notify all users that the router will be going down for maintenance. Which command would you use?

You would like to limit certain IP address to access a switch via VTY lines. Which of the following commands would allow you to do this?

Which command should be used to configure the amount of secure MAC addresses allowed on one secure port?

You are examining a routing table on a router you see a route that has an administrative distance of 110. Which symbol is indicated on the left hand side of the routing table?

Which routing protocol has a hop count limit of 15?

Which command would you use to back up a switch's NVRAM data to a server?

You want to view all of the VLAN names, statuses, and ports on a Cisco switch. Which IOS command would you use to view this specific information only?

Given the address of 172.16.0.0, and a CIDR value of /18, what addresses is used to broadcast traffic to all IP addresses in the mentioned network.

You need to create a static route to your central office. It must use an administrative distance of less than RIP. Which command would be used to accomplish this task?

You are verifying the status of an interface. You run the show interface command and notice that there are several CRC errors. What does this represent?

You are in the process of configuring inter-VLAN communication. You have configured a sub-interface for VLAN 20. Which command should be entered next?

The typical Cisco hierarchical network model consists of three layers. Which statement best describes the functions performed at the distribution layer?

Refer to the |h %5coutput%5ct14%5cmisc%5c100105eo411.html exhibit.

You have configured NTP as a client on router Branch. The output of the show ntp associations command indicates that router Branch has successfully synchronized with the NTP server. You now want to configure NTP as a client on switch SW1 as well. Which command should you use on switch SW1?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo320.html exhibit. Based on the output from the exhibit, which routing protocols are less trusted by the router then the configured administrative distance?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo325b.html exhibit. Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo325a.html output of R2. One of the computers in the stub network sends a packet to the router with an unknown address. To which address will router B send the unknown traffic?

What is the default port security violation mode?

Refer to the |h %5coutput%5ct14%5cmisc%5c100105eo416.html exhibit. The following output is displayed when the show access-lists command is executed:

Standard IP access list 1
|w |w |w deny host 192.168.1.11
|w |w |w permit any

This host should not have access to the 192.168.5.0 /24 network. Which command set should be used when applying this ACL to the router interface?

Which command is used to set a lease time of 15.5 hours for a DHCP IP address?

A frame has come in to a switch. The switch has check to see if a MAC address exists in the forwarding information base (FIB) before it can forward the frame. What will it do with the frame if the MAC address does not exists in the FIB?

What type of device establishes a barrier between a trusted, secure internal network and another outside network?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo305.html exhibit. What is the subnet mask of the 3rd child route for the 172.16.0.0 parent route?

Which type of IPv6 address should be used for the next-hop address with respect to IPv6 routing?

You are verifying the NAT configuration on your network. Which command is used to show failure to allocate a global address in real time?

Routers support packet-forwarding mechanisms. Which packet-forwarding mechanism is the most recent and preferred?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo310.html command output. You have run the show ip route command on RouterA in your network. What can you determine by reviewing the output of this command?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo303.html exhibit. If a PING packet originating from Switch A is sent to Switch B, which MAC address will the packet have when it arrives at Switch B?

You have configured an interface with port security. You have chosen to input the MAC addresses manually. This is an example of which feature?

You are troubleshooting a network connection problem on a computer. You need to refresh the DHCP configuration. Which command will you use?

Refer to the |h %5coutput%5ct6%5cmisc%5c100105eo212.html command output.

Which Cisco IOS command produced this output?

To which subnet does host 172.29.13.85/23 belong?

Refer to the |h %5coutput%5ct10%5cmisc%5c100105eo315.html exhibit. You want to configure a static route, so that users in the 10.0.0.0 network are able to locate resources located in the stub network. Which commands can you use to configure this static route? (Choose two.)

Which command can be used to encrypt all user account passwords in the user account database?

Which type of IPv6 address uses the FC00::/7 address block and is routable within an organization, but not across the Internet?

While calculating your results take a moment to complete our simple survey!

How likely is it that you would recommend TestPrep.Academy to a friend or colleague?